2010 ZR1 gets Detailed for that "Torched" look

I wanted to share the photos and detailing procedures involved in making this ‘Torched” ZR1 shine and sparkle better than it did when it rolled off the assembly line.

My client ordered a 2010 ZR1 way back in August of 2009 from Les Stanford Chevrolet with Museum delivery option. He had the VIN in hand and was ready to leave for Bowling Green in a couple of weeks. One week before the TPW week he changed his mind and decided to buy a 2010 GT3 instead. Ultimately he decided that the GT3 was not the one for him, and was reunited with the original ZR1 he had ordered in Aug 2009.

Before his purchase it sat for months, covered and only shown on several occasions, upon my initial inspection it looked like it had been wiped down many times with inferior techniques. It also had signs of RDS (Random Deep Scratches) and some abrasion marks from being covered either in storage or in transport. But beneath it all was a jewel just waiting to be finessed for its new owner.

My client and I had spoke several times in which I got a very clear understanding of how meticulous he was and what his expectations were. I then packed it up on a very cold rainy day to drive out to VV and perform my correction work and detailing……

Here are some photos of the ZR1 upon my initial inspection…













Some shots of the CF that was opaque and dull from cover abrasion and lack of TLC













Even the wheels lacked that sparkle and were stained and dull



Here the prep begins with a thorough bath and cleaning with Poly's Clear Tech Detailing Fluid.



After drying the vehicle with an SM Arnold Water Sprite all the decals are meticulously removed so the owner can save them.



A fresh piece of Clay Magic formed into a round little tortilla ready for the claying step



Claying begins and is done on all surfaces starting on the tops leaving the lowers for last. Even the lights, wheels and polycarbonate hood cover get a once over.





Wheels get detailed and polished, all the facets get Adams Metal Polish.



Wheel barrels and calipers are also left spotless.



Some compound I noticed the factory left in the rear intake.



Now the fun begins with my PCXP and M105 with a LC 7/8 Cyan Hydro Pad for the moderate defects, But first I make sure all vulnerable moldings get masked properly.





I then correct each panel one at a time using halogen lights and a Brinkman Swirl Finder hand held light.











Inspecting the panels using my lights....and Greg's massive display of lights as well.







Now that's how CF should pop......



Engine compartment gets a nice detailing as well.





Some much needed TLC on the interior as well.







After polishing the entire vehicle with the PCXP and a W8006 with M205, then removing it I then gave the ZR1 a coat of Adams Americana Paste Wax. After removing that I gave the vehicle a spritz of Opti Seal for even deeper results. Here are a couple of night shots as we finished a bit late that day...







So fast forward a few day's I was asked to come back over to do some door jamb correction for excessive scratches and for a more serious set of scratches on the CF roof and the hood. As I explained to Greg, I always believe in taking the least aggressive approach first. So working slow with a my Brinkman Sun Gun and a rotary polisher these more severe defects were methodically polished out.

















The last final touches with a boars hair detail brush in all the nooks and crannies.





The final shots of this glistening "Torch" red ZR1

































Thank for viewing and Happy New Year!

 

Very red indeed!

 

awesome job. The owner is a member of the Corvette Forum.

 

beautiful!

Question.... If you laid down paste wax first, wouldn't Opti-seal have bonding issues?

 

beautifull.
couple of questions, what did you use on the carbon roof? and are the wheels polished or chromed? looked polished.

Love that front brake caliper.

 

Awesome job !!!!

 

Great work! You're hard work really made that red pop.

-Kody-

 

Nice work, I have driven and rode in a ZR1 and WOW! Power is not lacking in it by any means! Great job and red looks bright as ever!

Yes, Dr G has said that the opti-seal solvents will go though the layer of nuba...said it "goes under the nuba" or something like that but IMO would dissolve it

 

Wow that is jaw dropping wet !!!! Awesome job !!!

 

Now, I HATE Corvettes, but this, is absolutely stunning. Great job! :applause:

 

Red is my favorite color when properly detailed. That red looks amazing. Very nice job!

 

Fantastic finish on that. Thanks for sharing.

 

:itsok:

 

Perfect detail as always man!!!!:thumb::thumb::thumb:

What is that thing on the floor that you use for your knees? (I ussume)

 

Very glossy. I like it!

 

Very nice work it looks great. But why did you apply a sealant (opti-seal) over a carnauba(adams premium) thats backwards.

 

Nice Job! I always liked the ZR1 especially in red.

 

Awesome work!

 

Excellent job, on an absolute beast of a car.

Very nice attention to detail.

 

Outstanding job! I love it.
Thanks, Joe D.